Home / Maytag dryer repair
Maytag Dryer Repair in Plano, TX
Gas and electric Maytag dryers, including Bravos models. What usually fails, why a broken belt can leave the dryer dead, and what a repair costs.
Last reviewed October 1, 2026. Written and reviewed by the Plano Dryer Pros team. How we create content
Plano Dryer Pros repairs Maytag gas and electric dryers in Plano, TX, including Bravos models. Common Maytag faults are a door latch or switch that stops the dryer starting, a worn or broken drive belt, a failed heating element and a blown thermal fuse. On many models a broken belt trips a belt switch, which can leave the dryer dead.
Key takeaways
- Common Maytag faults: door latch and switch, drive belt, heating element and thermal fuse.
- On many models a broken belt trips a belt switch, so the dryer may not start at all.
- Turn the drum by hand with the power off: no resistance suggests a broken belt.
- You get the full price in writing before any work starts.
Common Maytag dryer problems
Most Maytag calls come down to a few parts. Find your symptom and open the guide.
| What the dryer is doing | Likely part | Guide |
|---|---|---|
| Will not start, or seems dead | Door latch or switch, start switch, thermal fuse, or belt switch | Won’t start |
| Motor runs, drum does not turn | Broken drive belt | Belt, pulley and rollers |
| Tumbles, no heat or damp clothes | Heating element, thermal fuse, igniter or the vent | Dryer not heating |
| Squeals or thumps | Idler pulley, belt or drum rollers | Noisy dryer repair |
| Stops mid-cycle | Thermostat, door switch or sensor | Stops mid-cycle |
What are the most common Maytag dryer problems?
Common faults are a door latch or door switch that stops the dryer from starting, a worn or broken drive belt, a failed heating element or igniter that leaves clothes damp, and a blown thermal fuse. A blocked vent sits behind many heat failures. The guides below match each symptom to the likely part.
Won’t start: the door, the switches and the belt switch
A dryer that will not start is often a door problem, because the door switch must close before the motor runs. After that come the start switch, the thermal fuse and, on many models, a belt switch beside the idler pulley.
Why won’t my Maytag dryer start?
Start with the basics: the door fully latched, Start held firmly, and the breaker on, with both halves on an electric dryer. After that the usual causes are a door switch or latch, a start switch, a thermal fuse, or a broken belt tripping a belt switch. A meter test finds which one has failed.
Can a broken belt stop a Maytag dryer from starting?
On many Maytag dryers, yes. A belt switch near the idler pulley shuts the motor off when the belt breaks, so the dryer can seem dead rather than spinning without turning the drum. With the power off, turn the drum by hand: if it spins with no resistance, the belt has probably broken.
Heat and drying problems
A failed heating element or igniter leaves the dryer tumbling with damp clothes, and a blown thermal fuse can do the same or stop the dryer altogether. A blocked vent can cause all of these, so it is checked. See the thermal fuse guide and heating element replacement.
Why does my Maytag dryer run but not dry?
A failed heating element or igniter is a common cause, and so is a blocked vent or lint screen. On some models a dirty moisture sensor ends the cycle early with damp clothes. Check the lint screen and the vent first, then have the heat circuit tested with a meter.
Maytag Bravos and other models
Do you repair Maytag Bravos dryers?
Yes. Maytag Bravos dryers are repaired like other Maytag gas and electric dryers: the fault is found with a meter and the vent is checked. The model number, on the tag inside the door frame or on the back, lets the right part be matched, and the price is given in writing before any work starts.
What Maytag dryer repair costs in Plano
| Repair | Typical cost (parts and labor) |
|---|---|
| Vent path cleared, airflow restored | $100 to $200 |
| Thermal fuse or thermostat | $150 to $275 |
| Door switch or start switch | $150 to $250 |
| Belt, idler pulley or drum rollers | $200 to $375 |
| Heating element, or gas igniter or coils | $200 to $375 |
| Motor, blower wheel or drum bearing | $300 to $550 |
Typical Plano-area estimates, not a quote. See the dryer repair cost guide.
How much does Maytag dryer repair cost in Plano?
Most Maytag dryer repairs in the Plano area fall in the same typical range as other brands, about $150 to $400, parts and labor included. A thermal fuse or thermostat is usually the lower end, and a motor or control board the upper end. These are estimates, not a quote, so ask for the exact price in writing first.
How to book a Maytag dryer repair
- Call or request a repair online.
- Tell us it is a Maytag dryer, whether it is gas or electric, and what it is doing.
- Have the model number ready: it is on a tag inside the door frame or on the back.
- You get a time window for the visit.
- The technician diagnoses the fault and you get the full price in writing before any work starts.
Read about the whole service on the dryer repair service page. Maytag is a Whirlpool Corporation brand, so see Whirlpool dryer repair too.
About this page
Plano Dryer Pros is an independent repair service. It is not affiliated with, endorsed by or authorized by Whirlpool Corporation or the Maytag brand. Maytag and Bravos is a trademark of its owner and is used here only to describe the dryers we repair.
Sources
- iFixit: Maytag dryer not spinning, on the door switch, start switch and belt switch
- Sears Home Services: how to replace a thermal fuse in a dryer, on common causes of no heat
- Your dryer’s installation and service manual, which governs over any general guidance on this page
- Plano Dryer Pros estimates of typical local repair pricing, checked against national consumer cost guides for context. See our Editorial Policy.
Frequently asked questions
Is Maytag the same as Whirlpool?
Maytag is a Whirlpool Corporation brand, so many Maytag and Whirlpool dryers share similar designs and parts. They are not always interchangeable, so parts are matched by model number. The Whirlpool dryer repair page covers the faults common to both.
How do I find my Maytag dryer’s model number?
Look for a tag inside the door frame or on the back of the dryer. Have it ready when you call, because the model number lets the right belt, switch or element be matched. A photo of the tag is just as good.
Is it worth repairing an older Maytag dryer?
Usually, if it is under about 10 to 12 years old and the repair is a small part such as a belt, switch or element. If the repair nears half the price of a comparable new dryer, or the drum is rusted, replacing may be smarter.
Why does my Maytag dryer stop mid-cycle?
Often overheating from restricted airflow, which trips a thermostat, or a door switch that does not hold. A dirty moisture sensor can also end the cycle early. See the stops mid-cycle guide for the checks and the likely parts.
Do you repair Maytag gas dryers?
Yes. Gas dryers are repaired on their own gas parts: igniter, valve coils, flame sensor and burner. Gas piping and the shutoff valve are a plumber’s job. If you smell gas, leave the house and call 911 and Atmos Energy at 866.322.8667.
Can a loose door latch stop a Maytag dryer from starting?
Yes. If the latch does not catch properly, the door switch may never close, and the dryer will not start even though the door looks shut. A worn latch or a bent door can cause it, and the parts are inexpensive to replace.
Get your dryer working again
Call and a person will answer, or request a repair online. You get the full price in writing before any work starts.