Home / LG dryer repair in Plano
LG Dryer Repair in Plano, TX
LG dryers watch their own airflow and say so on the display. Here is what the codes mean, what usually goes wrong and what a repair costs.
Last reviewed October 1, 2026. Written and reviewed by the Plano Dryer Pros team. How we create content
Plano Dryer Pros repairs gas and electric LG dryers in Plano, TX. Many LG dryers use a Flow Sense system that shows D80, D90 or D95 when the exhaust airflow is restricted, which points to the vent first. Other common problems are no heat, noise and long drying times. Tell us the model number when you book.
Key takeaways
- Many LG dryers show D80, D90 or D95 when airflow is restricted: start with the vent.
- Find the model number on the tag inside the door frame, and tell us when you book.
- Other common problems are no heat, long drying times, noise and a door fault.
- Typical Plano repairs run about $150 to $400, and the price is in writing first.
Find your LG model number
Look for the tag inside the door frame or around the drum opening, and photograph it. LG dryer model numbers often begin with DLE for electric and DLG for gas, but the tag and the manual are the reliable guide. Tell us the brand and model number when you book, and we confirm whether we can service it before the visit is scheduled.
Where is the model number on an LG dryer?
Usually on a tag inside the door frame or around the drum opening. LG dryer model numbers often begin with DLE for electric models and DLG for gas models. Photograph the tag, and share it when you book, because parts differ between models. Your manual lists the model number too.
LG airflow codes: D80, D90 and D95
Many LG dryers use a Flow Sense system that measures how freely air leaves the dryer. When the exhaust is restricted, the display shows D80, D90 or D95, with a higher number meaning a worse restriction. Repair and parts sources describe D80 as roughly an 80 percent restriction, and at the highest level the dryer may stop. See the full guide: LG dryer D80 error: meaning and fix.
| Code | What it points to | What to do |
|---|---|---|
| D80 | A significant exhaust restriction | Clean the lint screen, check the duct behind the dryer and the outside hood |
| D90 | A heavier restriction | Stop and clear the whole vent run |
| D95 | A severe restriction, and the dryer may stop | Do not keep using it: clear the vent before the next load |
What does D80 mean on an LG dryer?
D80 is a Flow Sense warning that the exhaust airflow is restricted, often described as about an 80 percent blockage. It points to the vent: the lint screen, the duct behind the dryer, the wall duct or the outside hood. Clear the whole run, check for a crushed flex duct, and do not simply bypass the code.
Other common LG problems
| What you notice | Likely causes | Guide |
|---|---|---|
| No heat | Breaker, thermal fuse, thermostat, element, or on gas models the igniter or coils | Dryer not heating |
| Clothes take two cycles | A restricted vent, or a coated moisture sensor | Takes too long to dry |
| Noise | Worn rollers, belt, idler pulley or bearing | Noisy dryer repair |
| Will not start | Door switch, start switch, thermal fuse or control | Dryer won’t start |
| A door fault | Latch, catch or door switch | Door latch and catch |
What are the most common LG dryer problems?
Airflow warnings are the signature one, because LG dryers watch their own exhaust. After that come no heat, long drying times, noise and door faults. Most trace back to a restricted vent, a thermal fuse or thermostat, or a worn drive part. Clear the vent first, and note any code exactly.
Gas and electric LG dryers
- Electric models need a 240-volt circuit, and the usual no-heat causes are the breaker, the thermal fuse, a thermostat or the element
- Gas models need a gas supply and a 120-volt outlet, and the usual no-heat causes are the igniter, the valve coils, the flame sensor or a fuse
- If you smell gas near a gas dryer, leave the house and call 911 and Atmos Energy at 866.322.8667
Should I repair or replace my LG dryer?
For a small repair on a dryer under about 10 to 12 years old, repairing is usually worth it. A repeat airflow code after the vent is clear, or a repair near half the price of a comparable new dryer, tips toward replacing. Use the repair or replace calculator with your quote.
What an LG repair costs in Plano
| Repair | Typical cost (parts and labor) |
|---|---|
| Vent path cleared, airflow restored | $100 to $200 |
| Door switch or start switch | $150 to $250 |
| Thermal fuse or thermostat | $150 to $275 |
| Heating element, or gas igniter or coils | $200 to $375 |
| Motor, blower wheel or drum bearing | $300 to $550 |
Typical Plano-area estimates for any brand, not a quote. The exact price depends on the model and the part, and you get it in writing before any work starts. See the dryer repair cost guide and all brands we repair.
How much does LG dryer repair cost in Plano?
Most Plano dryer repairs cost about $150 to $400, parts and labor included, and the price depends on the model and the part, not the brand name. Clearing a vent, the usual fix for an airflow code, is about $100 to $200. These are estimates, not a quote, and you get the exact price in writing first.
Plano Dryer Pros is an independent repair service and is not affiliated with LG. LG is a trademark of its owner.
Sources
- Your dryer’s installation and service manual, which governs over any general guidance on this page
- Plano Dryer Pros estimates of typical local repair pricing, checked against national consumer cost guides for context. See our Editorial Policy.
- PartSelect: LG dryer codes D80, D90 and D95
Frequently asked questions
Can I bypass the D80 code on my LG dryer?
Bypassing hides a real restriction, which raises the fire risk and shortens the dryer’s life. Clear the vent instead. If the code returns after a clear vent, have the dryer and the sensor checked.
Why does my LG dryer show D80 right after a vent cleaning?
The restriction may be deeper in the run, in a crushed flex duct or at the outside hood, or a sensor fault may be reading wrongly. Check the duct behind the dryer and the hood, and have the airflow measured if it persists.
Is my LG dryer under warranty?
Check the date and the maker’s terms. If it is under the maker’s warranty, contact the maker first, because outside work can affect coverage.
Do you service both gas and electric LG dryers?
Yes. The model tag or the connections at the back show which you have. Tell us when you book, and we will plan the visit around the right parts.
What should I have ready when I book?
The model number, whether it is gas or electric, any code shown on the display, and what the dryer does. A photo of the model tag and the display saves time.
Get your dryer working again
Call and a person will answer, or request a repair online. You get the full price in writing before any work starts.